Hotan   DJ and power speaker system as in K+T 1/2017

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 100 dB
  • size (HxWxD): 1430 x 600 x 650 mm
  • frequency range (-8dB): 36 - 23000 Hz
  • crossover frequency(s): 900 Hz
  • speaker type: bass reflex
Enlarge

Hotan is a 2 way high-end pa speaker with hifi sound. The very linear driver-horn combination Faital Pro HF 200 and P-Audio PH-2380 is employed as tweeter. Two woofers Celestion FTR15-3070C are for the bass. Each of the loudspeakers feature two 15 inch woofers Celestion FTR15-3070C.

Hotan has been developed by Daniel Gattig and Dennis Frank.

The crossover consists of a 3rd order high-pass filter (18 dB per octave slope) for the tweeter. Two RCL circuits in parallel and one in series to the tweeter are smoothing the frequency response. The woofers are connected to a 1st order low-pass filter (6 dB per octave slope). An RCL circuit in parallel to the woofer is smoothing the frequency response. The Midwoofer is connected to a 2nd order low pass filter (12 dB per octave slope).

Between 50 Hz and 15000 Hz, the frequency response of this loudspeaker is very linear on axis. The decay spectrum is nearly perfect. At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are lower than 0.5% above 200 Hz and below 0.5% at 95 dB at 1 m .

Our kit consists of

  • Faital Pro HF 200 A - 2 inch compression driver
  • P-Audio 2 inch horn PH-2380
  • 2x Celestion woofer FTR15-3070C, 100dB
  • 4x Bass reflex tube HP100, 100x200 mm, black
  • 10x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • PE sealing tape, 5x2 mm, 7.5 m
  • 6x Damping Sonofil 100 x 35 cm for 20 litres
  • 2x Neutrik Speakon NL4MPR, connector round, 4 pin
  • 4m Speaker cable 2x2.5 mm2, transparent
  • 26x 1 pieces drive-in nuts M6, DIN 6930 g zinc-plated
  • 16x 1 pieces Allen screws M6x50, DIN 912, black
  • 10x
  • 4x Adam Hall 4907 rubber foot
  • 2x Handle recess GSM-220, steel 22x16 cm, black
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 5.6 uF / 400 Vdc
  • Audaphon MKP CAP Superior 6.8 uF / 400 Vdc
  • Audaphon MKP CAP Superior 15 uF / 400 Vdc
  • Audaphon MKT CAP 4.7 uF / 160 Vdc
  • Audaphon MKT CAP 5.6 uF / 160 Vdc
  • Audaphon MKT CAP 47 uF / 160 Vdc
  • Audaphon MKT CAP 68 uF / 160 Vdc
  • Mundorf baked varnish air core coil BL71, 0.015 mH
  • 1.0 mm air core coil, 1.2 mH/0.54 Ohm
  • 1.0 mm air core coil, 1.8 mH/0.7 Ohm
  • 0.7 mm air core coil, 0.27 mH/0.44 Ohm
  • Audaphon M core coil M12, 1.5 mH/0.16 0hm
  • Mundorf bs140 core coil 8.2mH/0.33Ohm
  • Mundorf H core coil H71, 22 mH/1.49 0hm
  • Metal-oxide resistor, 10W 8.2 Ohm 2% (grey-red-gold)
  • 3x Metal-oxide resistor, 10W 10 Ohm 2% (brown-black-black)
  • Metal-oxide resistor, 10W 22 Ohm 2% (red-red-black)

Kit without cabinet, price per speaker   EUR 1266,00 excl. VAT: € 1063.87 / $ 1148.97

Kit with high-end crossover

The high-end kit is delivered with copper foil and baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. All capacitors are of type polypropylen (MKP) and in series to the tweeter Clarity-Cap ESA are employed.

Kit with high-end-crossover without cabinet, price per speaker   EUR 1427,00 excl. VAT: € 1199.16 / $ 1295.09

Kit with high-power-crossover

The Hotan high-power crossover is made for using the Hotan for PA applications. In Hotan high power crossover is used high quality Clarity Cap PWA 400 V polypropylen (MKP) capacitors, big resistors and coils with a big wire diameter.

Kit with high-power-crossover without cabinet, price per speaker   EUR 1501,00 excl. VAT: € 1261.34 / $ 1362.25

Kit with high-power-high-end crossover

The high-end kit is delivered with high power copper foil and baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. All capacitors are of type polypropylen (MKP) 400 V and in series to the tweeter Clarity-Cap ESA 630 V are employed.

Kit with high-power-high-end-crossover without cabinet, price per speaker   EUR 1685,00 excl. VAT: € 1415.97 / $ 1529.24

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 15,70 excl. VAT: € 13.19 / $ 14.25

universal PCBs

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 220x155 mm, order no. I-8805002, price per unit:   EUR 11,80 excl. VAT: € 9.92 / $ 10.71
We recommend two boards per kit (four boards for a speaker pair)

Cabinet

Assembled cabinet with grey structure paint for Kit Hotan,
price per unit   - not available (_)

Assembled cabinet with black structure paint for Kit Hotan,
price per unit   - not available (_)


Measurements Hotan

Grafik

technical drawing Hotan

Grafik


Home   Klang+Ton Overview